M29W160EB-70N6

产品概述

IC Picture

图片仅供参考

制造商IC编号 M29W160EB-70N6
厂牌 MICRON/美光
IC 类别 FLASH-NOR
IC代码 29LV160 BOTTOM
共通IC编号 M 29W160EB - 70N6E NUX
M29W160EB-70N6 #160
M29W160EB-70N6 4000P
M29W160EB-70N6 X
M29W160EB-70N6E
M29W160EB-70N6E(LEADFREE)
M29W160EB-70N6ETSOP48STLF
M29W160EB-70N6F
M29W160EB-70N6L
M29W160EB-70N6T
M29W160EB70N6 #160 #160
M29W160EB70N6-ST
M29W160EB70N60E
M29W160EB70N60F
M29W160EB70N63
M29W160EB70N6E F
M29W160EB70N6E IC
M29W160EB70N6E M29W160EB-70N6E
M29W160EB70N6E PBF
M29W160EB70N6E(LF)
M29W160EB70N6E,(SMD
M29W160EB70N6E-N
M29W160EB70N6E-ST
M29W160EB70N6E90N6E
M29W160EB70N6EPBFREE
M29W160EB70N6F-N
M29W160EB70N6H
M29W160EB70N6T/BST

产品详情

脚位/封装 TSOP-48
外包装
无铅/环保 含铅
电压(伏) 3.3 V
温度规格 -40 C~+85 C
速度 70 NS
标准包装数量
标准外箱
Density 16M
Silicon Version E
Functionality Security Bottom boot (bottom blocks protected)
Package TSOP(NA = 48-pin ,12 x 20mm and NB = 56-pin,14 x 20mm)

General Description The M29W160ET/B (2Mb x8 or 1Mb x16) is a nonvolatile device that can be read, erased and reprogrammed. These operations can be performed using a single low voltage (2.7– 3.6V) supply. On power-up the memory defaults to read mode where it can be read in the same way as a ROM or EPROM. The device is divided into blocks that can be erased independently to preserve valid data while old data is erased. Each block can be protected independently to prevent accidental PROGRAM or ERASE commands from modifying the memory. PROGRAM and ERASE commands are written to the command interface of the memory. An on-chip program/erase controller simplifies the process of programming or erasing the memory by taking care of all of the special operations that are required to update the memory contents. The end of a PROGRAM or ERASE operation can be detected and any error conditions identified. The command set required to control the memory is consistent with JEDEC standards. The blocks in the memory are asymmetrically arranged. The first or last 64KB have been divided into four additional blocks. The 16KB boot block can be used for a small initialization code to start the microprocessor, the two 8 KB parameter blocks can be used for parameter storage, and the remaining 32KB is a small main block where the application may be stored. CE#, OE#, and WE# signals control the bus operation. They enable simple connection to most microprocessors, often without additional logic. The device supplied with all the bits erased (set to 1).

供应链有货

IC 编号 数量 生产年份
M29W160EB-70N6E 5,760 索取报价
M29W160EB-70N6E 12,331 索取报价
M29W160EB-70N6E 1,752 索取报价
M29W160EB-70N6E 6,336 索取报价
M29W160EB-70N6E 5,590 索取报价
M29W160EB-70N6E 319 0846+ 索取报价
M29W160EB-70N6 228 0505+ROHS 索取报价
M29W160EB-70N6F 149 1108+ 索取报价
M29W160EB-70N6F 2,262 索取报价
M29W160EB-70N6E 5,597 索取报价

FFFE/互通料号 (形式,腳位和功能对等)

IC 编号 脚位/封装 电压(伏) 速度 温度规格
M29W1601EB-70N6 TSOP-48 3.3 V 70 NS -40 C~+85 C
M29W160BB70N6 TSOP-48 3.3 V 70 NS -40 C~+85 C
M29W160D-EB70N6 TSOP-48 3.3 V 70 NS -40 C~+85 C
M29W160DB-70N6 TSOP-48 3.3 V 70 NS -40 C~+85 C
M29W160DB70N1/N6 TSOP-48 3.3 V 70 NS -40 C~+85 C
M29W160DB70N6T TSOP-48 3.3 V 70 NS -40 C~+85 C
M29W160E70N6 TSOP-48 3.3 V 70 NS -40 C~+85 C
M29W160EB70N1/N6 TSOP-48 3.3 V 70 NS -40 C~+85 C
M29W160EB7AN6F TSOP-48 3.3 V 70 NS -40 C~+85 C
M29W160EP-70N6 TSOP-48 3.3 V 70 NS -40 C~+85 C